Jump to content
www.BoXa.net

Search the Community

Showing results for tags 'Removal'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • BoXa.net Office
    • Announcements
    • Forum Suggestions
  • Porsche Zone
    • Boxster Chat
    • Porsche Talk
    • BoXa.net Meets, TrackDays & Events
    • Dealer Talk
    • Technical Questions & Answers
    • Members Rides
    • In Car & Home / Computer & Technology
    • Car Cleaning, Waxing & Polishing
    • Boxster Styling / Wheels, Tyres & Exhausts
    • Hey was that you I saw!
    • Insurance / Finance questions
    • Running Reports
    • How To
  • Social Zone
    • The Lounge / Bar
    • Newbie Lounge
    • Sports Section
    • Photography
  • Non Porsche Cars
    • Other marques besides Porkers!
    • Electric Cars
  • Sponsors Zone
    • AIB Insurance
    • Car Hood Warehouse
    • Cotswold Porsche Specialist
    • A Plan Specialist Insurance
  • BoXa.Net Market Place
    • For Sale / Selling Advice
    • Wanted / Buying Advice

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests


My Ride

Found 2 results

  1. Glovebox Removal - Performed on 2006 987 Boxster (Gen 1 or 987.1)NebulaOdyssey on BoXa.net BoXa profile Tools: 5/32” Allen Key (Hex)Torx T-25Torx T-20Old credit/debit/loyalty type card Steps: First you will need to remove the left side panel of the centre console. Use this guide if you need help with this step http://www.planet-9....removal-29.html Next, remove the cup holder. This has two hex screws visible from underneath when the glovebox is in the open position. I used an Allen Key as there is not much vertical height to fit a tool. Behind the cup holder there are two torx screws. Then down the right hand edge of the glovebox there are three more torx screws. Underneath the glovebox remove the black foam type covering, which has five plastic screw fittings (flat head or use a plastic card). Then while underneath, on the right hand side of the glovebox there is another torx screw. On the left hand side of the glove box, open the car door and pull off the black door seal near the glovebox section. Now remove the plastic insert by placing a card underneath and pulling away from the car, i.e. towards the open door. Once loose it pivots out. Here are the two clips holding it on, It pivots on the other end. Then you will be able to see and remove the two torx screws. One last screw is hiding behind the dash panel to the left of the glovebox. Looking straight on, wrap your fingers underneath the bottom and give it a tug straight out towards the back of the car. Once the bottom is loose give the top a little pull away from the front and it should come off easily. Behind here is the last torx screw to remove. Finally, with the glovebox door open pull the whole thing towards the back of the car, it may drop so support it. Now the glovebox can be lowered while being careful of any wires from the light and OBD II socket as I think these are attached. DONE! Reinstallation: Installation is the reverse of removal. The glovebox does need a little wiggling to locate it back into position. There are a few lugs to locate it all properly. Here is a PDF download, Click Here
  2. Ok, so without doubt this is the best money you will spend on a 986. It transforms the car from "a car" to "sports car" with just one reasonably simple swap. The kit Like many others, I got mine from Aliexpress (China). Even with post Brexit rates, I paid ~£39/$40.03 delivered for my shifter, and it arrived within a week (I paid extra for the quicker e-EMS shipping). Linky Mine arrived well packed The Tools My Box is a '99 2.5, so the fitting, and thus tools, may vary, but I used: - Flathead Screwdriver - Posidrive Screwdriver - T15 male Torx - T30 male Torx - 10mm Socket with Ratchet - 19mm Ring Spanner - Allen key (didn't check which size) - Stanley knife (or similar) - Marker Pen Removing the Centre Console I have the upper Centre Console delete, so this might make things easier for me. I didn't necessarily have to remove the blanking plate, but it save it falling off/getting damaged anyway... Next, unclip the gear gaiter. On this model, you unclip the front first, as the rear levers and slots towards the front. Pulling upwards on the gear knob will remove it. I've had mine off to replace the gaiter in the last 6 months, so it slid off easily. If your knob is a bit stiffer () watch you don't accidentally pull too hard and end up with it in your face (again, ). With this removed, there's a T15 Torx under where the front of the gaiter sits - remove. Next, you'll need to remove the ashtray (or if you have the other kit, then whatever ). There's normally a couple of T30 Torx screws under here, mine are more of a lightweight plastic securing rather than a traditional metal screw. Lift the switch bank out once you have undone the screws, then undo the T15 screw below, visible in the recess. Next, you will want to undo the switches. Either unplug them, or pop the switches out - this can be done by rocking them along the shortest axis (side to side), or with the aid of a flathead. The trim next to the handbrake should clip off easily... Next up, remove the rubber mat from the storage box. You'll find a single T15 securing the floor section underneath. If you want to adjust the handbrake cable, go directly for this part. Lift the floor section up. If you struggle, you get pop it up using your fingers, accessible under where you removed the trim at the side of the handbrake.. There's another screw in the bottom left of the pic, T15 again, and you will next need to lift out the coin holder to access another screw (T15) under this. The flathead is useful for popping the coinholder out, as it can be a bugger to do. Watch the lockable compartment microswitch that lives under here. You'll want to disconnect it first, or you'll risk breaking the switch itself (and you'll get a single beep from the horn each time you lock the car, should you c*ck it up). The whole centre console should now be loose and can be lifted out. You might need to angle this towards the driver's seat to clear the handbrake (this is how scratches can happen!) All being well, the Centre Console should now be removed and reveals the gear lever unit. Installing a Quick Shift Kit The plastic cover over the front of the gear change will lift off easily, revealing the cables and connectors... You'll want to mark the position of these within the black plastic sleeve - whichever way makes sense to you (this is why the marker pen was in the tools list!) Make sure its done well, as pen can rub off when handling. Once you have marked the cables, you can slide the plastic covers to allow the cable ends to be lifted out. Next, unclip the cables from the plastic housing.. The four 10mm nuts on each corner of the gear change unit can now be removed. The gear shift unit can then be lifted out, revealing the true colour of your carpet! You'll then need to lift the gear shifter unit out for further work. There are plastic bushes holding the gear change in. The easiest way to remove these is to cut out the lugs using a sharp blade. Once you have cut each bush free, they should pop out quite easily.. Once the bushes can been cut and removed, the shifter should be free to move out... Lift the old shifter out and remove the cable arm from the ball joint, then transfer to the new Shifter. It's recommended to replace these, but I didn't bother. Replaced with the new unit. It's easier to angle the longer 'stub' in first. Side by side comparison of old vs new. Note that the new one is slightly longer, which I found an issue with later on (and a solution).. The circlips should be secured in place, to stop the bushes slipping out... Make sure the ball joint/cable connectors are within the housing and not dangling below. Then temporarily adjust the lock nuts so there is no longitudinal slack, using a 19mm spanner and an Allen key. The gear shifter can then be 'bolted' back in place with the four 10mm nuts.. Note: Due to the extra length of the short shift, I found that the connector's spring kept fouling on the green plastic tab that lives on the bottom of the housing. The part number is 986.424.010.001 - although it's nigh on impossible to find out what it's purpose in life is. I've read that it is referred to as a 'coin deflector'. Either way, it needed to go. The cables can now be reattached to their original positions. Once exception to this, and a slight adjustment: The left cable position will allow a certain amount of adjustment for the central position of the gearknob. I adjusted mine quite significantly, as I found that neutral was too far over to the left. You could do the same for the right cable, but you have to be sure it can reach its extremities. People may talk about calibration and tools for this, but it's not that difficult to get things set up how you like if you're reasonably adept with the 'feel'. Just set things up and adjust, then readjust if required. Once you're happy with the adjustment, make sure there is no slack in the gear change and adjust as required. Again, once happy, you get put the centre console back on - in true Haynes Manual style, refitting is reverse of removal. In case you forgot, the passenger side switch are the white plugs. I found that the new 'bushes' found on the centre console too, so you could either adjust this end to compensate, or do as I did and 'modify' a small clearance in the console. It's not visible, so no worries there. All done, stand back and admire. I went for a short drive and was chuffed at the results Normal stuff applies - take your time, don't do anything silly, don't cut your fingers off with the knife, don't attempt if you're a clumsy danger to yourself, and not my fault of BoXa.net's fault if you make a dogs dinner of it all! Have fun!
×
×
  • Create New...